Quick Setup — Trezor Model One (Unofficial) 🎯

📦 What you need

• 🧩 Your Trezor Model One device (Model One) — in the box
• 🔌 USB cable (included)
• 💻 A computer with a modern browser (Chrome, Firefox, Edge)
• 📝 Pen & paper for your recovery seed (do NOT store it digitally)

⚠️ Important: This is an unofficial walkthrough. Always verify official resources before performing sensitive operations with crypto hardware.

🔌 1 — Power & connect

Plug your Trezor into the computer using the USB cable. The device screen will light up and show a welcome message. If the screen is blank, try a different USB port or cable.

• ✅ Confirm the device displays a welcome screen
• 🔁 If asked, confirm on the device when connecting to a new computer

🌐 2 — Open the official setup site (verify URL)

Open a browser and go to the official setup site recommended by your vendor (verify the link carefully). On a secure site, you'll see instructions that match the ones on your device.

🔎 Tip: Always check the browser address bar for the correct domain before proceeding. If unsure, visit the vendor's homepage and follow their official "Start" or "Get Started" link.

🛠️ 3 — Install firmware

The site will usually prompt to install the latest firmware. Follow on-screen instructions and confirm on the device. Firmware ensures your device runs secure, up-to-date software.

• ⏳ Wait for the installation to finish — do not unplug.
• 🔁 The device may reboot automatically.

🔑 4 — Set a PIN

Create a secure PIN on the device. This PIN protects the device itself — pick something memorable to you but hard for others to guess.

• 📱 The device will display digits — enter them using the device buttons.
• ⚠️ If you forget your PIN and you've lost your recovery seed, funds may be irretrievable.

🌱 5 — Write down your recovery seed

The device will generate a recovery seed (a list of 12–24 words). Write these words down in order on paper — do NOT take a photo or store them on your computer or cloud.

• ✍️ Use the included recovery card or a dedicated steel backup if you have one
• 🔐 Store the paper somewhere safe, ideally in multiple secure locations

🛑 Never share your recovery seed with anyone. Anyone with the seed can restore your wallet and take funds.

🧾 6 — Verify the seed & finish setup

The device typically asks you to confirm a few words from the seed to verify you recorded them correctly. Complete the verification and follow final on-screen steps.

💸 7 — Using your Trezor

Once setup is finished you can:

• 🔁 Receive cryptocurrencies by sharing your public receive address
• 📤 Send transactions — you'll confirm them on the device using the PIN
• 🔍 Use the supported wallet interface recommended in the setup site

✅ Always verify the receiving address on the device screen before confirming a transaction.

🛡️ Safety checklist

• 👀 Verify the website URL is correct before entering any confirmations
• 📵 Never type your seed into a computer or phone — it's for the device only
• 🔁 Keep firmware updated — updates patch security issues
• 🧭 Consider a hardware-backed backup (steel recovery) for long-term storage

⚙️ Troubleshooting & FAQs

• 🔌 Device not detected? Try a different USB cable or port; avoid USB hubs.
• 🧪 Firmware stuck? Do not unplug; reconnect and follow prompts. If problem persists, consult official support.
• 💬 Lost seed? If you lose your recovery seed and forget the PIN, funds are likely unrecoverable — keep the seed safe.

If you need advanced help, consult the official support channels from your device vendor — this page is a friendly guide, not official support.

🎉 You're done!

Congratulations — your Trezor Model One is set up and ready. Treat your recovery seed like gold, keep your firmware updated, and always verify addresses and domains when transacting.